“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Enclosure Cutout and Product Dimensions (in inches)
10-3/4" Max.
10" Min.
24-3/4"
ZIF36NMRH, Freezer
Handle on the left side, the door swings left to right.
35" Case
36" Overall
ZIF36NMLH, Freezer
Handle on the right side, the door swings right to left.
26-3/4"
84-1/2" Max.
83-1/2" Min.
Caution
73-1/2"
Refrigerators are much heavier at the top than
at the bottom – be extra careful when moving.
4"
• To achieve a flush fit, the finished cutout width must be
at least 36" wide.
*Finished Width
2-1/2
Wall View
Electrical
Area
• In a semi-flush installation, the finished cutout must
be 35-1/2".
6
• The electrical and water locations must be located as
shown for either type of installation.
5
24 3/4" Total
Depth
84-1/2" max
83-1/2" min
Finished
75" From Floor
to Bottom
of Electrical
Area
24-3/4"
Case
35"
Case
Width
Depth
Opening
5
5
Water Supply
3-1/2
3-1/2
84*
*36" for a flush installation.
35-1/2" Min. for a semi-flush installation.
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width. See installation examples.
36"
Frame to Frame
26-1/4"
Including
Handle
*Shipped at 84" installation height. Can be adjusted to
83-1/2" or 84-1/2" with Grille Panel Kits.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Installation at End of Run
1/2" Thick
Side Panels
Refrigerator
Cabinet
36"
37"
Finished Dim.
Roughed-In Dim.
Refrigerator Door
Cabinet
Note: 1/2" thick side panels shown. Side
panels can be any thickness. Add side
panel thickness to outside trim width
(36" or 72" for two models) to calculate
the rough-in dimension. The leading
(front) edge must be finished to match
surrounding cabinetry.
1/2" Thick
Side Panels
Finished Dim.
72"
73"
Rough-In Dim.
1/4" Thick
Side Panels
Finished Dim.
Rough-In Dim.
71 1/2"
72"
Refrigerator and Freezer
installed side-by-side
Side-By-Side Installation of Freezer and Refrigerator
*Finished Width
Electrical
2 1/2"
6"
Wall View
28 1/2"
6"
84"
5"
5"
24 3/4" Total
Depth
84 1/2" max
83 1/2" min
Finished
75" From Floor
to Bottom
of Electrical
Area
Opening
5"
Water Supply
36"
26"
3 1/2"
Freezer
Refrigerator
24-3/4"
36"
*72" min. for a flush installation
71-1/2" min. for a semi-flush installation
For a complete food storage center, install a Monogram
Freezer and Refrigerator side-by-side. For even more
capacity, install two refrigerators and/or two freezers.
• Order ZUG75 Unified Grille Panel Kit for one
continuous 3/4" custom grille panel.
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width.
• The electrical and water locations must be located
as shown for either type of installation. A separate
115V, 60Hz., 20 amp power supply is recommended
for each product.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Custom Panel Dimensions
A
Custom Grille Panel Dimensions
IMPORTANT: Maximum
weight for custom door
panel is 67 pounds and
9 pounds for the grille
panel.
Width
Height
Custom Grille Panels
Custom
Panel
1/4" THICK CUSTOM GRILLE PANEL
Panel
Width
Panel Height
to Fit Installation Height
B
83-1/2"
7-1/2"
84"
8"
84-1/2"
8-1/2"
35-1/8"
Rout for 3/4"
Handle Kits Only
See Details
Note: The grille panel frame is factory assembled
for 84" installation height. Order ZGC2 Grille Panel
Kit when installation height is more or less than 84".
3/4" THICK CUSTOM GRILLE PANEL
Requires ZKTR36 Trim Kit
CUSTOM DOOR PANEL SIZES
SIZES
A
B
Panel
Width
Panel Height
to Fit Installation Height
1/4" Panels
3/4" Panels
35-1/16"
35-1/16"
68-7/8"
68-15/16"
83-1/2"
7-3/4"
84"
84-1/2"
8-3/4"
3/4" Panels
(custom handles)
35-1/4"
8-1/4"
35-1/4"
68-15/16"
Note: A grille panel support is included with the
ZKTR36 trim kit and fits all installation heights.
Routing Detail
ZUG75 Grille Panel Dimensions
For Handle Kits Only
Rout Back Side of Panel
1-13/16"
This Grille Panel Kit should be used in combination
with ZKTR36H and ZKTR36RH, 3/4" panel kits.
Width
Height
ZUG75 Grille Panel
3/4" THICK CUSTOM GRILLE PANEL
Requires ZUG75 Trim Kit
1/4"
Max.
Appearance Side
Panel
Width
Panel Height
to Fit Installation Height
Rout the panel when installing a ZKHTR1 Custom
Handle Kit or ZKHTRSS1, Tubular Stainless Steel
Handle Kit.
83-1/2"
7-3/4"
84"
84-1/2"
8-3/4"
71-3/8"
8-1/4"
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
®
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
25"
Minimum
to Wall
Clearances
• Factory set for a 130° door swing. Order WX14X99
adjustable door stop to reduce swing to as little
as 90°.
90° Door Swing
130° Door Swing
When Installed into a corner:
Allow 25" for a full 130° door swing. Allow 15" for
pan removal. Allow 4" min. clearance when
door swing is adjusted to a 90° opening for pan
access, but pan removal is restricted.
36-3/4"
4" Min.
to Wall
90° door swing with
optional WX14X99
door stop.
0"
When installing an All-Refrigerator and All-Freezer
side-by-side, allow 25" for a full 130° door swing,
or 15" min. on the hinge sides for pan access.
25"
Min. to
Wall
25"
Min. to
Wall
130° Door Swing
130° Door Swing
ZUG75 Unified Grille Panel Kit is available for side-by-side
installations. See Trim Kit descriptions.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Design Information
Flush or Semi-Flush Enclosure Installation
Semi-Flush Installation
True Flush Installation
True Flush Installation
In a flush installation,
the freezer doors
Semi-Flush Installation
These freezers can
also be installed
will align evenly
semi-flush into an
enclosure using the
minimum cutout width.
The case trim creates
a frame around
with the front face
of adjacent cabinet
doors. The freezer
blends into the
0"
surrounding cabinetry.
the opening.
3/4"
Monogram built-in refrigerators and freezers can be
installed flush with typical 24-3/4" deep cabinetry.
Side Panel Requirements:
• Side panels are not required whenever the refrigerator or
freezer is installed into an enclosure or between pantry and
oven cabinets.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator
will project forward approximately 3/4" beyond the
front face of surrounding cabinetry.
• Side panels are required whenever the sides of the product
are exposed.
• Side panel sizes vary depending on the type of installation being
made.
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet manufacturer.
Be sure to provide the exact dimensions.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Features and Benefits
• 21.9 Cu. Ft. Freezer Capacity
• Wire Freezer Shelves (5 Adjustable,
1 Fixed, 1 Full-Width Fixed)
• Wire Baskets with Full-Extension Slides
(2 Regular, 4 Large)
• 2 Extra Large Wire Baskets with
Easy Access Lid and Full Extension Slides
• 8 Door Bins and Gallon Storage
• Automatic Defrost Sealed System Design
• Full Extension Slides
• Door Panels Required
• Model ZIF36NMRH – Door panels required
(right-handed door swing)
• Model ZIF36NMLH – Door panels required
(left-handed door swing)
Specification Revised 4/05
110156
|
Ei Electronics Smoke Alarm EI105C User Manual
Electro Voice Microphone PL24 User Manual
ETA Systems Impact Driver ETA S20RT User Manual
Fender Guitar 0194660 4662 User Manual
Fundex Games Board Games Cribbage User Manual
GE Coffeemaker 169161 User Manual
GE Freezer FUM13 User Manual
GE Monogram Gas Grill ZGG540LBPSS User Manual
GE Ventilation Hood ZVC42LSS User Manual
Giant Coffeemaker LP122A User Manual