Foundations Baby Furniture 100 SSC SM User Manual

Model 100-SSC-SM  
Clad Stainless Steel Changing Station  
Installation Instructions (Surface Mount)  
Thank you for purchasing a quality Foundations® product. Our goal is 100% consumer satisfaction!  
If, for any reason you are not satisfied or if you have questions regarding your product or installation,  
please contact our customer service team at 1-877-716-2757. Please DO NOT contact your distributor  
or reseller as we are better prepared to assist you.  
WARNING  
Failure to follow these warnings and the installation instructions could result in serious injury  
or death.  
Read all instructions before installing diaper changing station. Keep these instructions.  
DO NOT discard.  
SI258SM-D  
 
INSTALLATION  
Top  
Recommended Blocking:  
Wood double stud blocking is necessary. Contact an architect  
and building official to make sure the blocking is adequate and  
complies with building codes (Fig. a).  
8 1/4  
(210 mm)  
on center  
For A. D. A.  
Compliance  
45”  
(114 cm)  
32"  
(813 mm)  
on center  
A. F. F  
Fig. a  
1. Remove and discard Truss Head Spanner screws from unit back (Fig. b).  
Truss Head  
Spanner Screws  
2. Locate wood stud where left side of changing station will be mounted to  
the wall.  
3. For A. D. A. compliance, measure up 45” (114 cm) from the floor and mark  
the wall. This locates the position for the top left attachment hole.  
NOTE: Mark on wall MUST be in center of wood stud.  
4. Lay top section of changing station down on changing station bed (Fig. c) and  
align hole in top left corner of changing station with mark on wall and hold in place.  
5. Using a level and measuring tape, mark the remaining three (3) holes. After marking  
holes, set changing station down on ground.  
Fig. b  
6. Use a power drill and appropriate bit to drill four (4) holes in the wall. This may require  
2 people.  
NOTE 1: For wood studs:  
Surface-Mount  
Holes  
- If finished wall surface is tile or masonry over wood studs, use  
a 7/32” masonry bit for the pilot hole until you hit the wood  
stud, then change to 1/8” bit.  
- Use wood screws, finishing washers and flat washers (Fig. d).  
NOTE 2: For use with toggle anchors:  
- If finished wall surface has wood studs that are not 16” on center,  
has metal studs, or has an underlying surface of concrete block,  
use 1/2” bit.  
- Use machine screws and flat washers (Fig. e).  
Fig. c  
- For holes NOT located in a wood stud, toggle anchors MUST be  
used (Fig. f). See “Using Toggle Anchors” section.  
Flat  
Wood Stud  
Washer  
7. Rotate plastic top section back up so that mounting hardware goes through  
the plastic as well as the metal back (Fig. b).  
Finishing  
Washer  
NOTE: This unit incorporates a finishing collar that seats behind the changer’s  
outside flange. Center the collar as the unit is being tightened against the wall  
(Fig. g).  
Wood  
Screw  
8. Align holes in changing station with drilled holes and secure top left corner of changing  
station to wall stud using the appropriate screw and washer. Continue to secure the  
three (3) remaining corners using the appropriate screws and washers as described  
in Note 1 or Note 2.  
Fig. d  
Changing  
Station  
Toggle  
Anchor  
Collar  
Wood Stud  
Flat  
Washer  
Changing  
Station  
Wall  
Unit  
Machine  
Screw  
Fig. f  
Fig. e  
Fig. g  
2
 
Toggle  
Anchor  
Using Toggle Anchors (Fig. f):  
Wood Stud  
1. Insert metal end of toggle anchor into 1/2” hole.  
2. Slide zip strip down snugly against wall.  
3. Snap off break-away pieces of toggle anchor (Fig. h).  
Break-Away  
4. Align holes in changing station with toggle anchors and secure top left corner of  
changing station to wall using machine screws and flat washers. Continue to  
secure the three (3) remaining corners using machine screws and flat washers.  
Fig. h  
5. Ensure all four (4) screws are tight and snap caps over screw heads.  
OPERATION:  
Rotate base downward. Place infant on top of the changing surface. Use restraint  
system as described below. After child has been changed, remove restraint system  
and rotate base back up against the wall.  
Locking  
Tab  
Top Of  
Buckle  
USE OF RESTRAINT SYSTEM:  
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap  
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock  
the strap into place. Slide red locking tab over top of buckle (Fig. i). Reverse steps to loosen strap.  
Fig. i  
MAINTENANCE AND CLEANING:  
Check all hardware and components monthly or as required to ensure hardware is tight and there  
are no missing or damaged components. Take unit out of service if any component is missing or  
damaged and contact customer service to order replacement parts. Do not substitute parts.  
For replacement parts, contact customer service at 1-877-716-2757.  
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong  
chemical cleaners or cleaning agents that may be hazardous to children.  
WARNING  
Child should never be left unattended.  
Avoid serious injury from falling or sliding out. Always use restraint system.  
Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total  
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable condition to  
exist.  
3
 

Eagle Electronics Saw EGA510 User Manual
Edelbrock Automobile Parts YFZ450 User Manual
EdgeStar Ice Maker IB120SS User Manual
FieldServer Computer Drive FS 8700 115 User Manual
FOCUS Enhancements Projector TView Quad Scan Manual User Manual
Frigidaire Air Conditioner FRP12PTT2R User Manual
Fujitsu Air Conditioner AOU09RL2 User Manual
Gateway Personal Computer ALR 7200 User Manual
Gateway Personal Computer E 2300 User Manual
Gateway Personal Computer E 6100 User Manual