Eclipse Fujitsu Ten CD5423 User Manual

MODEL  
CD5423  
ESN E5 High-Power CD Receiver with  
Multi Control  
OWNER'S MANUAL  
We appreciate your purchase of this receiver.  
Please read through this manual for correct operation.  
We suggest that after reading it you keep this manual  
in a safe place for future reference.  
Warning  
• Do not place the vinyl storage bag over a person. It may cause  
a serious accident or death by suffocation.  
• Do not adjust the controls while driving the car. To adjust the  
controls, stop the car in a safe location.  
• To prevent accidents, store batteries for the remote control out  
of the reach of small children. In case a child swallows a  
battery, consult a physician immediately.  
• Do not disassemble or rebuild this product. Doing so may  
cause an accident, fire or electrical shock.  
• When it is necessary to replace the fuse, always use a fuse of  
the correct rating (number of amperes). Use of fuses with  
higher amperage ratings may cause a fire.  
• Do not operate the product in a malfunctioning condition, for  
instance, when the audio does not play. Doing so may result in  
an accident, fire or electrical shock.  
• If an abnormal situation occurs, such as foreign matter entering  
or liquid splashing on the product, or smoke or a strange odor  
emitting from the unit, shut off the product immediately and  
consult the dealer from whom you purchased it. Continued  
operation may cause an accident, fire or electrical shock.  
• Do not install this product in locations where it may obstruct the  
driver's view, or where it may endanger passengers in the  
vehicle. Otherwise, an accident or injury may result.  
• Do not install this product in locations where it may interfere  
with the operation of the steering wheel, shift lever, brake  
pedal, etc. Otherwise, an accident or injury may result.  
• When installing this product, never use existing nuts or bolts  
that secure parts of the fuel tank, or the steering or braking  
systems. Otherwise improper steering or braking or a fire may  
result.  
3
Warning  
• To prevent a short circuit from occurring, disconnect the  
battery's negative terminal before installing this product.  
Otherwise, an electric shock or injury may result.  
• When using an existing nut and/or bolt from the vehicle to  
ground this product, do not use any that secure parts of the  
steering or braking systems. Otherwise, an accident may result.  
• Bundle cables and harnesses with electrical tape or wire ties to  
prevent them from interfering with moving parts. If they should  
entangle the steering wheel, shift lever or brake pedal, an  
accident may result.  
• Never supply power to another electrical appliance by splicing  
or tapping into this product's power lead (wire). Otherwise, the  
current capacity of the wire will be exceeded, resulting in a fire  
or electric shock.  
• Never attempt to disassemble or modify the product.  
Otherwise, an accident, fire or electric shock may result.  
• When installing the product into a vehicle with a passenger  
side air bag, do not secure it to the air bag's cover or in places  
where it may impede air bag deployment. Otherwise, proper air  
bag operation may not be ensured in the event of an accident,  
causing injury or death.  
• When making holes using a drill or similar tool, be sure to wear  
protective eyewear. Otherwise, an injury such as loss of  
eyesight may result.  
• Exposed wires must be insulated with electrical tape.  
Otherwise, a short circuit, fire, or electric shock may result.  
4
Caution  
• Play the audio at a moderate volume level that permits you to  
hear sounds from outside the car. Driving without being able to  
hear outside sounds may result in an accident.  
• Keep foreign objects out of the disc slot. They may cause fire  
or electrical shock. Another possibility is that discs may be  
damaged or become stuck.  
• Do not stick your fingers or hands into the disc slot. Doing so  
may cause personal injury.  
• This product must be operated only as on-board equipment, or  
it may cause electrical shock or injury.  
• Do not play distorted sounds for long periods of time;  
the speakers may overheat and cause a fire.  
• This product uses an invisible laser light. In case a problem  
develops, be sure to consult the dealer from whom you  
purchased the product. Do not disassemble or rebuild the unit;  
rebuilding it may expose you and others to a dangerous laser  
emission (which would damage eyesight) or cause an  
accident.  
• Never use batteries other than those specified. Do not mix new  
and old cells. Doing so may cause a fire or personal injury due  
to a battery explosion or chemical leaks.  
• Pay attention to the (+) and (-) polarity of the battery when  
installing them in the product. Incorrect installation may cause  
personal injury or product damage spoilage due to a battery  
explosion or chemical leakage.  
• For best results, this product should be installed by a  
professional installer.  
Contact the dealer whom you purchased the product for an  
appointment.  
• When installing this product, be sure to use the supplied  
mounting hardware. If parts other than those supplied are  
used, the unit may be damaged internally, or may not be held  
in place securely and become dislodged.  
5
Caution  
• Avoid installing this product in places where it may get wet,  
such as near windows, or in places that are moist or dusty.  
Presence of liquid, moisture or dust inside this product can  
cause short circuiting, resulting in smoke or fire.  
• Do not install this product in locations where it cannot be  
fastened securely, such as places subject to frequent vibration.  
Otherwise, it may become dislodged and cause an accident or  
injury.  
• Do not block this product's vent or heat sink. If either is  
blocked, excessive heat build-up may occur and cause a fire.  
• If this product is not connected properly, a short circuit, fire or  
accident may occur.  
• When routing cables, use care so that they do not contact  
sharp metal parts such as brackets or screw tips. Otherwise, a  
short circuit, electric shock, fire or accident may result.  
• Do not obstruct the vent on this product. If blocked, excessive  
heat build-up may occur and cause a fire.  
6
Table of Contents  
Operating precautions...............................................10  
Notes on operation.......................................................................10  
About compact discs ....................................................................11  
About cleaning a CD ....................................................................13  
Names of controls and parts ....................................14  
ESN (Key CD) security operating procedure ..........15  
How to program the Key CD ........................................................15  
How to cancel the Key CD ...........................................................16  
How to change the Key CD..........................................................17  
How to resume normal operation (ESN security lock out)............17  
What happens if an incorrect CD is inserted?..............................18  
How to turn the security indicator on/off.......................................19  
How to read the Electronic Serial Number ...................................19  
Basic operation..........................................................20  
Turning the power on and off .......................................................20  
Listening to a CD..........................................................................21  
Listening to the tuner....................................................................22  
Adjusting audio volume ................................................................23  
Switching audio control modes.....................................................24  
Enabling the loudness control ......................................................25  
Making changes with Display Adjustment Mode..........................26  
Making changes with Function Mode...........................................27  
Making changes with Sound Adjustment Mode ...........................30  
Others...........................................................................................33  
How to operate the CD player..................................34  
Listening to CDs...........................................................................34  
Advancing to the next track or returning to the beginning of  
the track being played ..................................................................35  
Fast Forward/Rewind ...................................................................35  
Playing the beginning of tracks (SCAN).......................................35  
Repeating the same track (REPEAT)...........................................36  
Playing tracks in random order (RANDOM) .................................36  
Ejecting the disc ...........................................................................37  
Creating a title for a CD................................................................38  
Changing a previously set title .....................................................40  
Deleting a previously created title ................................................41  
Displaying CD TEXT ....................................................................42  
7
How to operate the MP3 player ................................43  
About MP3....................................................................................43  
Listening to MP3 file.....................................................................46  
Advancing to the next track (file) or returning to the beginning of  
the track (file) being played ..........................................................47  
Skipping to the next or previous folder.........................................47  
Return to the root directory of the CD ..........................................47  
Playing the beginning of files (SCAN) ..........................................48  
Repeating the same file (REPEAT)..............................................48  
Playing files in random order (RANDOM) ....................................49  
Displaying title ..............................................................................49  
How to operate the tuner...........................................50  
Tuning to a station........................................................................50  
Entering stations into memory automatically  
(The automatic preset mode: ASM) .............................................51  
Manually setting stations into memory .........................................52  
Preset station scan.......................................................................53  
FM reception characteristics ........................................................54  
How to use an optional Card remote control..........56  
Precautions in use of the remote control......................................56  
Cleaning the remote control .........................................................56  
Turning the power on/off ..............................................................57  
Adjusting the audio volume ..........................................................57  
Switching playback modes...........................................................58  
How to play the tuner ...................................................................58  
How to play CDs...........................................................................59  
Enabling the optional E-COM feature...........................................60  
Switching the remote control settings...........................................61  
Replacing the battery ...................................................................62  
How to use an optional NOB remote control ..........63  
Turning the power on/off ..............................................................63  
Adjusting the audio volume ..........................................................63  
Switching playback modes...........................................................64  
How to play the tuner ...................................................................64  
How to play CDs...........................................................................65  
Illuminating the NOB remote control ............................................66  
Enabling the optional E-COM feature...........................................66  
Switching the remote control settings...........................................67  
Replacing the battery ...................................................................68  
8
How to operate the receiver with an optional  
CD changer connected..............................................70  
Listening to a CD..........................................................................70  
Advancing to the next track or returning to the beginning of  
the track being played ..................................................................70  
Fast Forward/Rewind ...................................................................70  
Playing the beginning of tracks (SCAN).......................................71  
Repeating the same track (REPEAT)...........................................71  
Playing tracks in random order (RANDOM) .................................72  
Skipping to the next or previous CD.............................................72  
Specifying a CD to play................................................................73  
How to operate the receiver with an optional  
DSP/EQ unit connected.............................................74  
How to operate the DSP functions ...............................................74  
How to operate the EQ functions .................................................77  
Others .........................................................................80  
Connecting Portable Audio Players to the AUX Jack...................80  
If you have a question:..............................................81  
Displayed information (for troubleshooting)..................................82  
Specifications ............................................................85  
Before installation .....................................................86  
Components.................................................................................86  
Setting the system-selector switch...............................................86  
Installation angle ..........................................................................87  
Mounting instruction.................................................88  
Mounting the main unit.................................................................88  
Names of lead wires and destinations .........................................90  
System .........................................................................................91  
9
Operating precautions  
Operating precautions  
<Your CD5423 will perform well over a long period of time through correct  
handling and care.>  
Notes on operation  
• For your safety, play only at volume levels that allow outside sounds to be  
heard.  
• We recommend using with this player a disc with  
the logo shown to the left.  
• You can play music CDs(CD-R/CD-RW) on this  
player. Be sure to use discs that have been  
properly processed.  
Depending on the editing equipment used, some  
discs may not play properly.  
• Do not insert anything other than a CD into the  
disc slot.  
Do not insert any foreign objects, such as coins or  
credit cards, into the disc slot. Be especially  
watchful of children’s mischief in this regard.  
• Avoid severe mechanical shock.  
When the player is subjected to severe vibration  
while traveling over a rough surface, playback  
may be intermittent. When a situation like this  
occurs, resume playback after returning to a  
smoother road.  
• About dew condensation.  
In cold or rainy weather, just as the interior glass  
surface gets fogged, dew (water condensation)  
may also settle on the deck. When this occurs,  
disc playback may become intermittent or  
impossible. Dehumidify the air in the vehicle for a  
while before resuming playback.  
• Cleaning the disc slot.  
The disc slot tends to get dusty. Clean it  
occasionally to prevent accumulated dust from  
scratching the discs.  
10  
Operating precautions  
About compact discs  
• The signal recorded on a compact disc is read by a laser beam, so  
nothing touches the disc surface. A scratch on the recorded surface or a  
badly warped disc may cause deteriorated sound quality or intermittent  
playback. Observe the following precautions to ensure high quality sound  
performance:  
• Do not leave an ejected disc in the disc slot  
for very long; the disc may warp. Discs  
should be stored in their cases and kept  
away from high temperature and humidity.  
• Do not stick a piece of paper or tape on, nor  
write on or scratch either side of a disc.  
• Discs spin at a high speed inside the deck.  
Keep cracked or warped discs out of the  
player to avoid damaging it.  
• Avoid touching the recorded surface when  
handling a disc; handle discs by their edges.  
11  
Operating precautions  
About brand new CDs  
About CD accessories  
• You may notice that some brand  
new discs are rough around the  
center hole or outside edge.  
Remove the rough edges with  
the side of a ballpoint pen, etc.  
Rough edges may prevent  
proper loading in the deck.  
Flakes from the rough edges  
may also stick to the recorded  
surface and interfere with  
playback.  
• Do not use accessories  
(stabilizers, protective seals, laser  
lens cleaners, etc.) sold for  
“improving sound performance”  
or “protecting CDs.” The changes  
in CD thickness or outside  
dimensions made by these  
accessories may cause problems  
in the player.  
Rough Edges  
Ballpoint  
pen  
Please be sure NOT to attach any  
ring-shape protector (or other  
accessory) to your discs. Those  
protectors are commercially  
available and said to protect disc  
and to improve sound quality  
(and antivibration effect), but they  
can do more harm than good in  
regular uses. The most common  
problems are Insert/Eject related  
problems and "No playback"  
problems due to the protector  
ring that came off in the disc  
mechanism.  
Rough  
Edges  
Flakes  
Recorded surface  
12  
Operating precautions  
About borrowed CDs  
About irregularly-shaped CDs  
Specially-shaped CDs, like  
heart-shaped or octagonal CDs,  
cannot be played. Do not  
attempt to play them, even with  
an adapter, since they may  
damage the player.  
Do not use a CD with glue or  
remnants of adhesive tape or  
labels. They may cause the CD  
to get stuck inside or damage  
the deck.  
How to remove CDs  
When removing the ejected disc,  
pull it straight out along the slot.  
Pressing downward in the  
process may scratch the  
recorded surface of the disc.  
OKAY  
About cleaning a CD  
Use a commercially available compact disc  
cleaner to clean a CD, wiping lightly from the  
center to the edge.  
Do not use benzine, thinner, LP record spray  
or other cleaners on CDs. They may damage  
a CDs finish.  
XXXX  
13  
Names of controls and parts  
Names of controls and parts  
Front view  
①②③ ④  
④ ⑤⑥⑦  
⑬⑫  
⑪⑩⑨⑦  
With the front open  
Never place an object or rest your hands or the like on the front  
panel.  
Caution  
Switches disc modes and switches to AUX mode.  
[DISC] button  
[E-COM] button*  
[OPEN] button  
Activates and deactivates mute.  
Opens/closes front panel and adjusts angle.  
Selects radio preset channels and performs disc mode  
functions.  
Buttons [1] to [6]  
[SOUND] button  
[DISP] button  
Turns the sound adjustment mode ON/OFF.  
Turns screen adjustment mode ON/OFF and switches screen  
display.  
Automatically finds radio reception and fast forward/rewind.  
Selects radio stations and CD tracks.  
Returns to previous screen.  
[SEEK /FAST ] button  
[SEL] button  
[RTN] button  
Turns function mode ON/OFF.  
[FUNC] button  
Resets deck functions to default settings.  
Turns deck power ON/OFF.  
[RESET] button  
[PWR] button  
Switches to radio mode and switches radio bands.  
Adjusts volume and performs other functions.  
Inserts compact discs.  
[FM AM] button  
[AUDIO CONTROL] button  
Disc slot  
*: Double function button  
"E-COM" & "MUTE" functions  
14  
ESN (Key CD) security operating procedure  
ESN (Key CD) security operating procedure  
Button [6]  
[FUNC] button  
How to program the Key CD  
Check that the Power is OFF.  
1
Press and hold button [6], then the [FUNC] button, and  
hold both for more than one second.  
2
A [SEC] message appears, then in two seconds it will change  
to [DISC].  
The front panel opens; the CD5423 is now ready to accept your  
Key CD in the CD slot.  
Insert the CD into the slot.  
3
The front panel closes.  
A [SEC] message appears, the front panel opens, then the Key  
CD is ejected.  
If there is a problem with the inserted CD, an [ERR] message  
will appear for two seconds and the CD will be ejected. Reinsert  
ATTENTION  
the ejected CD.  
If a CD causes the [ERR] message to appear twice in a row, a  
[CHANGE] message will appear for two seconds. Try another  
CD.  
The Security indicator will flash whenever the vehicles ignition  
is switched off.  
15  
ESN (Key CD) security operating procedure  
Button [6]  
[FUNC] button  
How to cancel the Key CD  
Turn OFF the Power.  
1
Press and hold button [6], then the [FUNC] button, and  
hold both for more than one second.  
2
A [SEC] message appears, then in two seconds it will change  
to [DISC].  
The front panel opens; the CD5423 is now ready to accept your  
Key CD in the CD slot.  
Insert your Key CD into the slot.  
3
The front panel closes.  
A [CANCEL] message appears, the front panel opens, then the  
Key CD is ejected.  
The Key CD is cancelled.  
This process cancels the protection for the ESN deck.  
If power to the ESN deck is disconnected, then  
ATTENTION  
reconnected, a Key CD will not need to be inserted in order  
to return the unit to normal operation.  
Inserting a CD other than the Key CD will not cancel the  
protection. Instead, the display will show [ERR] for two  
seconds, then the normal CD playback mode will activate.  
16  
ESN (Key CD) security operating procedure  
How to change the Key CD  
First, cancel the existing Key CD.  
1
Refer to How to cancel the Key CD.”  
Next, program a new Key CD.  
2
Refer to How to program the Key CD.”  
How to resume normal operation  
(ESN security lock out)  
If power is disconnected while ESN security is active (a Key CD was  
programmed), operation is disabled until power is restored and the  
unit unlocked. Follow this procedure to resume normal operation.  
When the power is turned on after disconnecting the  
battery power, a [SEC] message will appear for two  
1
seconds. Thereafter, the message changes to [DISC]  
and the CD5423 is ready to accept your Key CD into the  
slot.  
Insert your Key CD.  
2
If the correct CD is inserted, an [OK] message will appear for  
two seconds and the CD will begin playing.  
If an incorrect CD is inserted, an [ERR] message will appear  
for two seconds, after which the CD will be ejected.  
ATTENTION  
You must use the same CD used for Key CD programming;  
a duplicate CD may not work properly.  
17  
ESN (Key CD) security operating procedure  
Button [6]  
[FUNC] button  
What happens if an incorrect CD is  
inserted?  
An [ERR] message will be appear, then change to a  
flashing [DISC], then the CD will be ejected.  
1
You will have five uninterrupted attempts to insert the correct  
CD.  
After the 5th incorrect attempt, the display reads [HELP].  
2
If [HELP] appears on the screen, press button [6], then  
the [FUNC] button, and hold them for five seconds.  
3
Press the [FUNC] button.  
4
You will have five more attempts the correct disc.  
Number of errors: Numbers indicated the number of errors that  
occurred.  
ATTENTION  
O Note O  
If after 10 tries the correct Key CD is not inserted, the display  
reads [CALL800]; the unit must be returned to Eclipse to be  
reset. In this case, please contact your Eclipse dealer for  
assistance or call Eclipse directly at (800) 233-2216.  
Your key CD can be easily forgotten. Write the  
album name in a reminder note (See Page 95).  
18  
ESN (Key CD) security operating procedure  
Button [2]  
Button [4]  
[FUNC] button  
How to turn the security indicator on/off  
Once ESN security is activated, the indicator flashes whenever the  
vehicles ignition is turned off, warning potential thieves that the unit  
is protected. However, if you do not want this visible deterrent, it may  
be turned off.  
With the power OFF, press button [2], then the [FUNC]  
button and hold both for more than one second.  
1
[IND. FLASH] or [IND. -----] appears on the display.  
2
[IND. FLASH] means the security indicator will flash when the  
vehicles ignition is off, and [IND. -----] means it will not. Repeat  
the above steps to reactivate the flash mode.  
How to read the Electronic Serial Number  
Turn OFF the Power.  
1
Press button [4], then the [FUNC] button, and hold both  
for more than one second.  
2
[ESN] appears on the display, followed by an eight-digit  
number; this number is your electronic serial number (ESN).  
You may use this number to identify your Eclipse CD5423 in  
the event it is recovered after being stolen.  
19  
Basic operation  
Basic operation  
[PWR] button  
This section covers basic operating procedures. For additional  
details, please refer to the sections on specific functions.  
Turning the power on and off  
Turning the power on and off.  
When the power is turned on, the state used when the power was  
turned off such as CD and tuner playing is restored.  
When the vehicle has no ACC position on the ignition switch, care is  
needed when turning off the deck. Follow Step 2 or Step 3 when  
turning off the power.  
When power is OFF, press [PWR] button.  
1
The power will come ON.  
When power is ON, press the [PWR] button for less than  
two seconds.  
2
The power will go OFF and the deck will be in Standby.  
When power is ON, press the [PWR] button for more  
than two seconds.  
3
The power will go completely OFF.  
If a car is not equipped with an ACC position (for example, a  
European car), keep the [PWR] button depressed for more than  
ATTENTION  
two seconds.  
20  
Basic operation  
[OPEN] button  
[DISC] button  
Listening to a CD  
Press the [OPEN] button.  
1
The front panel opens.  
Insert a CD into the disc slot, label side up.  
2
The CD will immediately start playing.  
When a CD is already loaded, press the [DISC] button to switch  
to the CD mode.  
ATTENTION  
21  
Basic operation  
Buttons [1] to [6]  
[SEEK ] button  
[SEL]  
button  
[FAST ] button  
[FM AM] button  
Listening to the tuner  
Press the [FM AM] button.  
1
This will turn the tuner on.  
Press the [FM AM] button to switch to the desired FM or  
AM bands.  
2
3
4
Radio bands will switch from FM1 FM2 FM3 AM in  
order each time the button is pressed.  
Turn the [SEL] button to the left or right to tune to a  
station.  
Turn to the right: Tunes to higher frequencies.  
Turn to the left: Tunes to lower frequencies.  
Press the [SEEK /FAST ] button to start the automatic  
station search.  
[SEEK ] button: Starts searching toward higher frequencies.  
[FAST ] button: Starts searching toward lower frequencies.  
If stations have been stored in memory, pressing a button  
from [1] to [6] will directly select a station. (Refer to the section  
ATTENTION  
“Manually setting stations into memory” on page 52)  
22  
Basic operation  
[E-COM] button  
[AUDIO CONTROL] button  
Adjusting audio volume  
Turn the [AUDIO CONTROL] button to the left or right.  
1
Turn to the right: Increases the volume.  
Turn to the left: Decreases the volume.  
Press the [E-COM] button for more than one second if E-COM is  
connected and less than one second if E-COM is not connected  
to cut the volume or restore it instantly.  
ATTENTION  
Warning  
Do not adjust the volume or other controls while driving the  
vehicle. Do so only while parked in a safe location.  
23  
Basic operation  
[AUDIO CONTROL] button  
Switching audio control modes  
Various audio control modes may be fine-tuned using this  
procedure.  
Press the [AUDIO CONTROL] button for less than one  
second to select the item to be adjusted.  
1
Modes will switch in the order shown below each time the  
button is pressed.  
VOL  
BASS*  
TREB*  
BAL  
FAD  
NON-F  
*: These mode cannot be adjusted when the Hide-Away EQ/DSP  
Sound Processor (2301) is connected.  
VOL (VOLUME) Mode  
Adjusts volume.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Increases the volume.  
Turn to the left: Decreases the volume.  
BASS Mode  
Adjusts bass level.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes low sounds.  
Turn to the left: Softens low sounds.  
TREB (TREBLE) Mode  
Adjusts treble level.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes high sounds.  
Turn to the left: Softens high sounds.  
24  
Basic operation  
[AUDIO CONTROL] button  
BAL (BALANCE) Mode  
Adjusts left/right speaker balance.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes right speakers.  
Turn to the left: Emphasizes left speakers.  
FAD (FADER) Mode  
Adjusts front/rear speaker balance.  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Emphasizes front speakers.  
Turn to the left: Emphasizes rear speakers.  
NON-F (NON-FADER) Mode  
Adjusts non-fader level (for connected sub-woofers, etc.).  
Turn the [AUDIO CONTROL] button to the left or right.  
Turn to the right: Increases level.  
Turn to the left: Decreases level.  
Enabling the loudness control  
The loudness control may be turned on to emphasize low and high  
frequencies at low volume levels.  
Loudness compensates for the apparent weakness of low and high  
frequencies at low volume by boosting the bass and treble levels.  
Press and hold the [AUDIO CONTROL] button until the  
[LOUD ON] display appears on the screen.  
1
To disable the loudness feature, repeat the above procedure to  
display the [LOUD OFF] indication.  
ATTENTION  
25  
Basic operation  
[DISP] button  
[SEL]  
button  
[RTN] button  
Making changes with Display Adjustment Mode  
This function allows adjustment of display contrast and changing  
illumination colors.  
Press the [DISP] button.  
1
Enters Display Adjustment Mode.  
Contrast adjustment  
Adjust the display contrast to the best level in accordance with  
the angle of viewing.  
Turn [SEL] button to select CONTRAST.  
1
2
Press the [SEL] button.  
Enters Contrast Adjustment Mode.  
Turn [SEL] button to adjust contrast.  
Turn to the right: Increases level.  
Turn to the left: Decreases level.  
Press the [RTN] button.  
At this time, other adjustments can also be made in Display  
Adjustment Mode.  
Press the [DISP] button to exit Display Adjustment  
Mode.  
3
4
5
Changing Illumination Color  
1
2
Turn [SEL] button to select ILL COLOR.  
Press the [SEL] button.  
The screen for changing the illumination color will appear.  
Turn [SEL] button to select GREEN or RED.  
3
4
Press the [RTN] button.  
At this time, other adjustments can also be made in Display  
Adjustment Mode.  
Press the [DISP] button to exit Display Adjustment  
5
Mode.  
26  
Basic operation  
[SEL]  
button  
[FUNC] button  
Making changes with Function Mode  
A variety of settings can be changed.  
Press the [FUNC] button.  
1
The function mode is activated.  
Turn [SEL] button in either direction to display setting  
items for selection.  
2
Setting items will be displayed in the following order when the  
[SEL] button is turned to the right.  
DISC TITLE *1  
GUIDE TONE  
REMOTE *2  
CLOCK DISP  
CLOCK ADJ  
1:  
*
Cannot make settings other than for CD or CD changer  
operation.  
(Refer to page 38 for details on CD operation.)  
2:  
*
Refer to pages 61 and 67 for details on remote control  
operation.  
27  
Basic operation  
[SEL]  
button  
[FUNC] button  
[RTN] button  
Disabling the guide tone feature (for button operation)  
The receiver is set at the factory to emit a beep tone in  
response to button operation. The guide tone feature may be  
disabled in the following procedure:  
Turn [SEL] button to select GUIDE TONE.  
1
2
Press the [SEL] button.  
The Guide Tone Mode will be switched ON/OFF.  
Turn [SEL] button to select ON or OFF.  
3
4
Press the [RTN] button.  
At this time, other adjustments can also be made in  
Function Mode.  
Press the [FUNC] button to exit Function Mode.  
5
CLOCK DISPLAY on/off  
Switches the clock display to ON/OFF.  
Turn [SEL] button to select CLOCK DISP.  
1
2
Press the [SEL] button.  
The clock display ON/OFF mode is activated.  
Turn [SEL] button to select ON or OFF.  
3
4
Press the [RTN] button.  
At this time, other adjustments can also be made in  
Function Mode.  
Press the [FUNC] button to exit Function Mode.  
5
28  
Basic operation  
[SEEK ] button  
[SEL]  
button  
[FUNC] button  
[RTN] button  
[FAST ] button  
Setting the Time  
This receiver uses the 12-hour display notation.  
Turn [SEL] button to select CLOCK ADJ.  
1
2
Press the [SEL] button.  
The clock adjustment mode is activated.  
Turn [SEL] button to display the item to be selected for  
adjustment.  
3
Hours, minutes or exact hour will be switched each time the  
button is turned.  
Press the [SEEK /FAST ] button.  
4
[SEEK ] button: Turns the time forward.  
[FAST ] button: Turns the time back.  
To set the clock to 0 minutes, 0 seconds (an exact hour),  
press the [SEEK /FAST ] button.  
For example:  
At 3:29: Pressing the [SEEK /FAST ] button returns to 3:00.  
At 3:30: Pressing the [SEEK /FAST ] button advance to 4:00.  
Press the [RTN] button.  
At this time, other adjustments can also be made in  
Function Mode.  
5
6
Press the [FUNC] button to exit Function Mode.  
29  
Basic operation  
[SOUND] button  
[SEL]  
button  
Making changes with Sound Adjustment Mode  
Used to adjust acoustic feature in the vehicle.  
Press the [SOUND] button.  
1
The sound adjustment mode is activated.  
Turn [SEL] button in either direction to display setting  
items for selection.  
2
Setting items will be displayed in the following order when the  
[SEL] button is turned to the right.  
DSP*  
EQ*  
BASS/TREB  
X-OVER FR  
X-OVER NF  
Non-FADER  
*: This is displayed only if DSP/EQ (2301) is connected.  
(Refer to page 74 for details on DSP/EQ operation.)  
30  
Basic operation  
[SOUND] button  
[SEL]  
button  
[RTN] button  
SETTING BASS/TREBLE  
These modes adjust bass (low sounds) and treble (high  
sounds).  
Turn [SEL] button to select BASS/TREB.  
Press the [SEL] button.  
1
2
The BASS/TREB setting mode is activated.  
Turn [SEL] button to select BASS/TREB.  
Press the [SEL] button.  
3
4
The frequency selection mode is activated.  
Turn [SEL] button to display the frequency to be  
selected.  
5
6
Press the [RTN] button.  
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
7
Disabling the Cross Over (F,R) function  
Here, the HPF (high-pass filter) to the front and rear preouts  
can be switched ON and OFF.  
Since the high-pass filter passes only higher ranges (lower  
ranges are cut off), efficient playback is enabled by cutting off  
lower-range elements not needed for the mid to higher range  
speaker.  
Turn [SEL] button to select X-OVER FR.  
Press the [SEL] button.  
1
2
The cross over (front/rear) switching mode is activated.  
Turn [SEL] button to select ON or OFF.  
Press the [RTN] button.  
3
4
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
5
31  
Basic operation  
[SOUND] button  
[SEL]  
button  
[RTN] button  
Disabling the Cross Over (NF) function  
Here, the LPF (low-pass filter) to the non-fader pre-out can be  
switched ON and OFF.  
Since the low-pass filter passes only lower ranges (higher  
ranges are cut off), efficient playback is enabled by cutting off  
mid to higher range elements not needed for a woofer.  
Turn [SEL] button to select X-OVER NF.  
Press the [SEL] button.  
1
2
The cross over (non-fader) switching mode is activated.  
Turn [SEL] button to select ON or OFF.  
Press the [RTN] button.  
3
4
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
5
Switching Non-Fader modes  
Sound integration can be improved for full range speakers and  
woofers by switching the phase.  
Switch the phase and select an integration method that is  
compatible.  
Turn [SEL] button to select Non-FADER.  
Press the [SEL] button.  
1
2
The non-fader setting mode is activated.  
Turn [SEL] button to select NORMAL or REVERSE.  
Press the [RTN] button.  
3
4
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
5
32  
Basic operation  
[E-COM] button  
[OPEN] button  
Others  
Enabling E-COM feature  
Press the [E-COM] button for one second.  
1
Pressing the button will switch the E-COM feature on or off.  
Adjustment of the front panel angle  
Press and hold the [OPEN] button for more than one  
second.  
1
While holding the button, the front panel opens regardless  
of the stage. The operation stops when the limit of  
adjustable angles is reached.  
Press the [OPEN] button again for more than one  
second.  
2
The front panel will be completely closed.  
Operations assistance function  
Buttons to be used will flash and operation order will be shown  
when in display adjustment mode, function mode or sound  
adjustment mode.  
33  
How to operate the CD player  
How to operate the CD player  
[DISC] button  
First press the [DISC] button to switch to the disc mode. It is  
assumed here that a CD has already been loaded into the unit.  
Listening to CDs  
Press the [DISC] button.  
1
This starts CD play.  
If an external CD changer is connected, each additional press  
of the [DISC] button will switch modes from CD changer 1  
CD changer 2 CD player.  
A changer or player with no discs loaded will be skipped.  
•Playback may be intermittent when there is a scratch on a CD  
or when the recorded side is dirty.  
Caution  
•Only two external CD changers may be connected.  
34  
How to operate the CD player  
Button [4] [SEEK ] button  
[SEL]  
button  
[FAST ] button  
Advancing to the next track or returning to  
the beginning of the track being played  
Turn the [SEL] button to the left or right.  
1
Turn to the right: Advances to the next track.  
Turn to the left: Returns to the beginning of the track being  
played. (Repeat turning for previous tracks.)  
Fast Forward/Rewind  
Fast forward or rewind the song currently being played.  
Press and hold the [SEEK ] or [FAST ] button.  
1
[SEEK ] button: Fast forward.  
[FAST ] button: Rewind.  
Playing the beginning of tracks (SCAN)  
Press button [4].  
1
Pressing the button causes the player to move up to the next  
track and play it for 10 seconds, then move up to the next track  
and play it for 10 seconds, and so on until the button is  
pressed again.  
•To continue playing a desired track, press the button again to  
stop scanning.  
ATTENTION  
•After the entire disc is scanned once, ordinary playback starts  
from the point where scanning started.  
35  
How to operate the CD player  
Buttons [5] and [6]  
Repeating the same track (REPEAT)  
Press button [5] to repeat the track being played.  
1
To cancel, press button [5] again.  
Playing tracks in random order (RANDOM)  
Press button [6] to play the tracks in random order.  
1
To cancel, press button [6] again.  
•Doing random playback, press button [5] to repeat the track  
being played. To cancel repeat play (go back to random play),  
ATTENTION  
press button [5] again.  
During playback a particular track: The track being played is  
played repeatedly.  
During searching: The following track is played repeatedly.  
•Occasionally the same track happens to be played (selected)  
two or more times in a row; this is normal operation and is no  
sign of a problem.  
•When any of the functions - “Playing the beginning of tracks,”  
“Repeating the same track” and “Playing tracks in random  
order” - is selected, a message such as [SCAN], [REPEAT] or  
[RANDOM] appears on the display to verify the current function.  
36  
How to operate the CD player  
[OPEN] button  
Ejecting the disc  
Press the [OPEN] button for less than one second.  
The front panel opens fully and ejects the disc.  
1
Remove the disc and press the [OPEN] button.  
2
The front panel returns to the angle before the disc ejection. If  
left alone for 15 seconds after the disc ejection, the front panel  
returns to the angle before the disc ejection after the BEEP  
sound.  
•Do not drive with the front panel open. The panel may cause  
unexpected personal injury during a panic stop, or the like.  
Caution  
•Do not attempt to close the front panel by hand. Doing so may  
damage the panel.  
37  
How to operate the CD player  
[SEEK ] button  
[SEL]  
button  
[FUNC] button  
[RTN] button  
[FAST ] button  
Creating a title for a CD  
A CD title may be created, attached and displayed for your discs. If  
external CD changers are connected, a title for a CD will be created  
in the same way. It is assumed here that the CD to be titled is  
playing.  
No CD text disc can be set.  
ATTENTION  
Press the [FUNC] button while in the Disc mode.  
1
Turn [SEL] button to select DISC TITLE.  
2
Press the [SEL] button.  
3
The disc title setting mode is activated.  
Press the [SEEK ] button to select the character type.  
4
Pressing the button will switch types from [ABC] (alphabet  
characters) to [123] (numeric characters) and then [!&?]  
(symbols).  
Press either [SEL] or [FAST ] button to select the  
position in which to enter the character.  
5
The character will be inserted where the cursor is flashing:  
[SEL] button:  
Moves the cursor to the right.  
[FAST ] button: Advances the cursor to the left.  
38  
How to operate the CD player  
Turn the [SEL] button to the left or right to select  
characters.  
6
Turn to the right: Advances the character forward in its type.  
Turn to the left: Moves the character backward in its type.  
[Upper-case alphabet characters] Initial value [A] [Right direction]  
...  
ABCXYZ  
[Numeric characters] Initial value [1] [Right direction]  
...  
123890  
[Symbol] Initial value [!]  
[Right direction]  
! " # $ % & ( ) * + , . / : ; < = > ? @ ´ _  
To change the type of character to be entered, repeat steps 3  
and 4.  
ATTENTION  
A maximum of 8 characters may be entered per title.  
30 titles can be stored.  
If the number of discs that can be memorized is exceeded, the  
information about the disc whose playing time is oldest is  
deleted.  
Press the [RTN] button.  
7
8
At this time, other adjustments can also be made in Function  
Mode.  
Press the [FUNC] button to exit Function Mode.  
The CD title is now memorized.  
39  
How to operate the CD player  
[SEL]  
button  
[FUNC] button  
[RTN] button  
[FAST ] button  
Changing a previously set title  
If external CD changers are connected, a previously set title for a CD  
will be changed in the same way. It is assumed here that the disc  
mode is selected.  
Press the [FUNC] button while in the Disc mode.  
1
Turn [SEL] button to select DISC TITLE.  
2
Press the [SEL] button.  
3
The disc title setting mode is activated.  
Press either [SEL] or [FAST ] button to move the cursor  
to the position in the title for inserting or changing  
characters.  
4
[SEL] button:  
Moves the cursor to the right.  
[FAST ] button: Advances the cursor to the left.  
Turn the [SEL] button to the left or right to select  
characters.  
5
Turn to the right: Advances the character forward in its type.  
Turn to the left: Moves the character backward in its type.  
To leave a space blank, follow these steps.  
1.Select and flash the space to be blank.  
ATTENTION  
2.Turn the [SEL] button to make a blank space flashing.  
3.Press the [SEL] button to move.  
Press the [RTN] button.  
6
7
At this time, other adjustments can also be made in Function  
Mode.  
Press the [FUNC] button to exit Function Mode.  
The CD title entry process is now completed.  
40  
How to operate the CD player  
Button [6]  
[SEL]  
button  
[FUNC] button  
[RTN] button  
Deleting a previously created title  
If external CD changers are connected, a previously created title for  
a CD will be deleted in the same way. It is assumed here that the  
disc mode is selected.  
Press the [FUNC] button while in the Disc mode.  
1
Turn [SEL] button to select DISC TITLE.  
2
Press the [SEL] button.  
3
The CD title being played at this point will be deleted.  
Hold the [6] button down for more than two seconds.  
4
The title has now been deleted.  
Press the [RTN] button.  
5
At this time, other adjustments can also be made in Function  
Mode.  
Press the [FUNC] button to exit Function Mode.  
6
41  
How to operate the CD player  
[DISP] button  
Displaying CD TEXT  
Only the built-in CD player supports CD TEXT. It can not be  
displayed with the optional CD changer. If the CD came with a logo  
shown below, it is recorded with a disc title and track titles. These  
information will be displayed during playback.  
Press the [DISP] button for more than one second.  
1
Pressing the [DISP] button while text is displayed scrolls the  
display in the order DISC title TRACK title, and then the  
display stops with the TRACK title.  
42  
How to operate the MP3 player  
How to operate the MP3 player  
MP3 files can only be played when E-COM is connected.  
About MP3  
The making of MP3 files by recording from sources such as  
broadcasts, records, recordings, videos and live performances  
ATTENTION  
without permission from the copyright holder for uses other than  
personal enjoyment is prohibited.  
What is MP3?  
MP3 (MPEG Audio Layer III) is a standard format for audio compression  
technology. By using MP3, a file can be compressed to one-tenth the size  
of the original.  
This deck has limitations on MP3 file standards and recorded media and  
formats that can be used.  
Playable MP3 file standards  
• Supported standards: MPEG-1 Audio Layer III  
MPEG-2 Audio Layer III  
• Supported sampling frequencies: 22.05, 44.1 (kHz)  
• Supported bit rate: 8, 16, 24, 32, 40, 48, 56, 64, 80, 96, 112, 128 (kbps)  
* Does not support free format.  
• Supported channel modes: stereo, joint stereo, monaural  
ID3 tags  
MP3 files have an "ID3 Tag" that allows input of information so that data  
such as song title and artist can be saved.  
This deck supports ID3v.1.0 and ID3v.1.1 tags.  
43  
How to operate the MP3 player  
Media  
Media capable of playing MP3 includes CD-ROM and CD-R discs.  
Compared to CD-ROM media commonly used for music discs, CD-R discs  
are fragile in high temperature/high humidity environments and one section  
of the CD-R may become incapable of playback. Fingerprints or scratches  
on the disc may prevent playback or cause skipping during playback.  
Sections of a CD-R may deteriorate if left inside a vehicle for long periods of  
time. It is also recommended that CD-R discs be kept in a light-blocking  
case because the discs are vulnerable to ultra-violet light.  
Format of discs  
The format of discs to be used must be ISO9660 Level 1 or Level 2.  
Control items for this standard are as follows:  
• Maximum characters for folder names/file names: 15  
• Allowable characters for folder names/file names: A~Z, 0~9, _ (underscore)  
• Number of files possible on a single disc:  
65535*1  
[Configuration example for CD supporting MP3]  
Root directory (F1)  
F2  
Folder 2  
001.mp3  
002.mp3  
003.mp3  
004.txt  
Number of files possible on a single disc is  
65535.  
Files aside from MP3 files (Example: 004.txt)  
also count as single files.  
005.mp3  
Folder 158  
Folder 159  
F158  
F159  
001.mp3  
002.mp3  
Folder 300  
F300  
• Number of folders possible on a single disc: 300*2  
• Number of files possible in a single folder: 300  
*1: Files aside from MP3 files (other than ".mp3" file extension) are also  
counted as single files.  
*2: A root directory is counted as one folder.  
44  
How to operate the MP3 player  
File names  
Only files with the MP3 file extension ".mp3" can be recognized as MP3 and  
played. Be sure to save MP3 files with the ".mp3" file extension. The "MP"  
letters of the file extension will be recognized whether entered as  
uppercase letters or lowercase letters.  
If the ".mp3" file extension is attached to a file other than an  
MP3 file, that file will be mistakenly recognized by the deck as  
Caution  
an MP3 file and played, resulting in loud noise output that can  
damage the speakers. Be sure to avoid attaching the ".mp3" file  
extension to files that are not MP3 files.  
Multi-sessions  
Multi-sessions are supported, and playing of CD-R disc with annotated MP3  
files is possible. However, when "Track at once" has been written, close the  
session or process the warning message. Standardize the format of each  
session without changing format.  
Playing MP3  
When a disc with recorded MP3 files is inserted, the deck first checks all the  
files on the disc. Checking of the files will be completed within 10 seconds  
of disc insertion, and the first MP3 file will begin playing. If the disc check is  
not completed within 10 seconds, the player will go into standby mode. No  
sound is output while the deck is checking the files on the disc. It is  
recommended that the disc be recorded without files other than MP3 files  
and without unnecessary folders in order to speed up the checking of disc  
files by the deck.  
Display order of MP3 file/folder names  
Names of MP3 folders and files within the same level are displayed in the  
following order.  
1. MP3 folders displayed first, by ascending order of numbers, letters.  
2. Files displayed next, by ascending order of numbers, letters.  
45  
How to operate the MP3 player  
[DISC] button  
Listening to MP3 file  
Press the [DISC] button.  
1
This starts MP3 file play.  
If an external CD changer is connected, each additional press  
of the [DISC] button will switch modes from CD changer 1 ➔  
CD changer 2 CD player.  
A changer or player with no discs loaded will be skipped.  
•Playback may be intermittent when there is a scratch on a CD  
or when the recorded side is dirty.  
Caution  
•Only two external CD changers may be connected.  
46  
How to operate the MP3 player  
[SEL]  
button  
Buttons [1] and [2]  
[RTN] button  
Advancing to the next track (file) or returning to  
the beginning of the track (file) being played  
Turn the [SEL] button to the left or right.  
1
Turn to the right: Advances to the next track (file).  
Turn to the left: Returns to the beginning of the track (file)  
being played.  
Repeat turning for previous tracks (files).  
Skipping to the next or previous folder  
Press button [1] or [2].  
1
Button [1]: Selects the next folder.  
Button [2]: Selects the next lower folder.  
Return to the root directory of the CD  
In the root directory, when a file cannot replay, the system will  
return to the first file that can perform a replay. (In the  
configuration example, the file is returning to 001.mp3. See  
page 44.)  
Press the [RTN] button.  
1
47  
How to operate the MP3 player  
Buttons [4] and [5]  
Playing the beginning of files (SCAN)  
Press button [4].  
1
Press the button briefly to play just the first 10 seconds of each  
song for all the files in the same layer of the folder being  
played.  
Pressing the button until [ALL SCAN] is displayed will play just  
the first 10 seconds of the first song in each folder.  
•To coutinue playing a desired file, press the button again to  
stop scanning.  
ATTENTION  
•After the entire disc is scanned once, ordinary playback starts  
from the point where scanning started.  
Repeating the same file (REPEAT)  
Press button [5].  
1
Press the button briefly to repeat the file being played.  
Pressing the button until [ALL REPEAT] is displayed will repeat  
all the files in the same layer as the folder being played.  
To cancel, press button [5] again.  
48  
How to operate the MP3 player  
[DISP] button  
Buttons [5] and [6]  
Playing files in random order (RANDOM)  
Press button [6].  
1
Press the button briefly to randomly play the files in the same  
layer as the folder being played.  
Pressing the button until [ALL RANDOM] is displayed will  
randomly play the files in all the folders.  
To cancel, press button [6] again.  
•Doing random playback, press button [5] to repeat the file  
being played. To cancel repeat play (go back to random play),  
ATTENTION  
press button [5] again.  
During playback a particular file: The file being played is played  
repeatedly.  
During searching: The following file is played repeatedly.  
•Occasionally the same file happens to be played (selected) two  
or more times in a row; this is normal operation and is no sign of  
a problem.  
Displaying title  
Press the [DISP] button for more than one second.  
1
Each time the button is pressed, the following will be displayed  
in order.  
Folder Name/File Name* Tag  
*: The display area shows a maximum of 10 characters and  
then scrolls to display the remaining characters.  
After the folder name is displayed, the file name will be  
displayed by scrolling. After the file name is scrolled, the  
display will be fixed.  
49  
How to operate the tuner  
How to operate the tuner  
[SEEK ] button  
[SEL]  
button  
[FM AM] button  
[FAST ] button  
First, press the [FM AM] button to start tuner operation.  
There are automatic and manual methods for setting stations in  
memory. The receiver will accept up to 24 stations in memory: six in  
AM and 18 in FM (6 each for FM1, FM2 and FM3.) (Initial setting)  
Tuning to a station  
Press the [FM AM] button to switch to the desired FM or  
AM bands.  
1
Radio bands will switch from FM1 FM2 FM3 AM in  
order each time the button is pressed.  
Turn the [SEL] button to the left or right to tune to a  
station.  
2
Turn to the right: Tunes to higher frequencies.  
Turn to the left: Tunes to lower frequencies.  
Press the [SEEK /FAST ] button to start the automatic  
station search.  
3
[SEEK ] button: Starts searching toward higher frequencies.  
[FAST ] button: Starts searching toward lower frequencies.  
At times, it may be difficult to maintain optimum reception  
because the antenna affixed to your vehicle is in motion  
ATTENTION  
constantly (relative to the broadcast antenna), encountering  
continuous variation in the received radio signals’ strength. Other  
factors affecting reception include interference from natural  
obstacles, sign posts, etc.  
50  
How to operate the tuner  
Buttons [1] to [6]  
[SEL]  
button  
[FM AM] button  
Entering stations into memory automatically  
(The automatic preset mode: ASM)  
Press the [FM AM] button to switch to the desired FM or  
AM bands.  
1
Radio bands will switch from FM1 FM2 FM3 AM in  
order each time the button is pressed.  
Press the [SEL] button for more than one second until a  
beep is heard.  
2
The automatic preset mode starts.  
The [ASM ON] indicator on the screen flashes, and stations are  
automatically entered in memory under buttons [1] to [6].  
These buttons are called preset buttons.  
•Press any numbered button to select the station whose  
frequency is indicated right above the button.  
ATTENTION  
•When a new station is set in memory, the station previously set  
in memory will be deleted.  
•If there are fewer than six receivable stations, the stations set in  
the remaining buttons will be retained.  
51  
How to operate the tuner  
Buttons [1] to [6]  
[SEL]  
button  
[FM AM] button  
Manually setting stations into memory  
This section covers the setting of stations in memory under the  
numbered buttons.  
Press the [FM AM] button to switch between FM and AM.  
1
Turn the [SEL] button to the right or left to tune to the  
station to be entered in memory.  
2
Select any button, from [1] to [6], and press it for more  
than two seconds.  
3
The tuned station is now memorized and set in the button  
selected. Repeat the procedure to set additional manually  
tuned stations in memory, in turn, for buttons [1] to [6]. These  
buttons are called the preset buttons.  
If the vehicle’s battery is disconnected (for repairs to the  
vehicle or for removing the receiver), all stations in memory will  
Caution  
be lost. In such a case, set stations in memory again.  
52  
How to operate the tuner  
Buttons [1] to [6]  
[SEL]  
button  
Preset station scan  
This function enables reception of all the stations in the preset  
buttons for five seconds each.  
Press the [SEL] button for less than one second.  
1
[P SCAN] will appear at the display, and stations stored under  
preset buttons [1] through [6] will be played for five seconds  
each.  
To stop the preset scan mode at a desired station, press  
the [SEL] button again.  
2
The receiver will stay tuned to the desired station.  
53  
How to operate the tuner  
FM reception characteristics  
In general, FM has much better tonal quality than AM. However, FM  
and FM stereo reception encounter several characteristic problems  
not encountered with AM. FM is more difficult to receive than AM in a  
moving vehicle. The following are explanatory notes on what to  
expect from FM reception and on how to get satisfactory  
performance.  
FM RECEPTION DIFFERS FROM AM  
A characteristic of transmitted signals is that lower frequencies  
travel further. FM frequencies are much higher than AM’s  
(similar to a ray of light): they won’t bend but they will reflect.  
Often, they will be interrupted by tall buildings, mountains, etc.,  
taking direct and indirect paths to your vehicle’s antenna. The  
distance at which FM stations can be received satisfactorily is  
usually not nearly as far as that which AM stations can be  
received.  
AM Radio Waves  
Ionosphere  
FM Radio Waves  
Ionosphere  
FADING OUT  
In weak signal or “fringe” reception areas, FM stations may  
fade out completely, or fade in and out. When driving in weak  
signal areas, such as near hills, through valleys or tunnels,  
among tall buildings, etc., you may encounter unusual noise  
interference. THIS IS NOT A TUNER PROBLEM. In this case,  
you can only wait until you are in a better reception area, tune  
to a stronger station, or reduce the treble level.  
54  
How to operate the tuner  
RECEPTION AREA OF FM BROADCASTS  
A home receiver can catch weak FM stereo signals through the  
use of a tall, directional or ultra-sensitive antenna. In a moving  
vehicle, the area for good reception is limited because of  
varying conditions encountered while driving, including the  
types and heights of broadcast antenna structures, signal  
strength, engine noise, etc. For best reception with manual  
antenna, extend the antenna mast as far as possible.  
Transmitting Antenna 100 Meters High  
Effective Radiation Power 1kW  
FM Stereo Auto Radio 20 km  
FM Monaural Auto Radio 50 km  
Home FM Stereo Receiver 100 km  
Reception quality varies depending on the power of the FM  
station, natural and artificial barriers,weather conditions, etc.  
MULTIPATH  
The reflection characteristics of FM waves cause another  
problem called multipathFM wave signals reflecting off of  
buildings, mountains, etc. When the antenna receives direct  
and reflected waves at the same time, distortion of sound in the  
treble range often occurs, such as static or harsh-sounding  
voices. THIS IS NOT A TUNER PROBLEM. Only moving to  
another area with a clearer signal path can remedy the  
situation.  
DIRECT  
WAVE  
55  
How to use an optional Card remote control  
How to use an optional Card remote control  
Precautions in use of the remote control  
• Be careful when handling the control, especially because it is  
small and light. Dropping or striking it hard may damage it,  
wear out the battery or cause a malfunction.  
• Keep the remote control free of moisture, dust and water. Do  
not subject it to shock.  
• Do not place the remote control unit where it will get hot, such  
as on the dashboard or near a heater vent. Allowing the  
remote control unit to overheat may warp its case or cause  
other problems.  
• Do not operate the remote control unit while driving because  
doing so could cause an accident.  
• When using the remote control, point it directly at the remote  
control light receptor.  
• The light receptor may not operate correctly if it is exposed to  
bright light such as direct sunlight.  
• Be sure to press the [PWR] button on the main unit for more  
than two seconds to shut it down before leaving the car, or the  
car battery may be run down. When the main unit is shut down,  
the remote control will not work.  
• Remove the batteries from the remote control unit whenever it  
is not to be used for a long time.  
Cleaning the remote control  
• Use a dry cloth to keep the unit clean. If the remote control unit  
gets extremely dirty, clean it with a cloth moistened in dilute  
liquid detergent. Do not use alcohol or thinner; these  
compounds may damage the finish.  
• In no event should benzine or thinner be used. These  
substances will damage the case or finish.  
56  
How to use an optional Card remote control  
[PWR]  
Remote-control  
button  
light receptor  
[+] button  
[-] button  
[MUTE]  
button  
Turning the power on/off  
When the power is turned on, the state used when the power was  
turned off such as CD and tuner playing is restored.  
Press the [PWR] button.  
1
The power turns on or off each time the button is pressed.  
When the main unit is shut down, the remote control will not work.  
ATTENTION  
Adjusting the audio volume  
Press the [+] or [-] button.  
1
[+] button: Increases the volume.  
] button: Decreases the volume.  
[
-
Cutting the volume instantly (muting)  
Press the [MUTE] button for more than one second to cut the  
volume or restore it instantly.  
Press the [MUTE] button for more than one second if E-COM is  
connected and less than one second if E-COM is not connected  
ATTENTION  
to cut the volume or restore it instantly.  
57  
How to use an optional Card remote control  
[MODE] button  
[BAND] button  
Switching playback modes  
Press the [MODE] button.  
1
Press the button to switch modes in the following sequence:  
Tuner  
Disc  
AUX  
How to play the tuner  
Select the tuner mode first.  
Selecting the FM/AM band  
Press the [BAND] button.  
1
Each press will switch tuner modes from FM1 FM2 ➔  
FM3 AM.  
58  
How to use an optional Card remote control  
[BAND] button  
[
[
TUNE•SEEK ] buttons  
PRESET CH ] buttons  
Selecting a station (manually or automatically)  
A short press of the button will allow manual station tuning.  
Pressing for more than one second will start automatic tuning.  
Press the [ TUNE•SEEK ] button.  
1
[
[
] button: Tunes to higher frequency stations.  
] button: Tunes to lower frequency stations.  
Selecting preset stations  
A total of six stations may be selected (preset tuning) out of  
those already set in memory through the main unit. (Refer to  
Manually setting stations into memory,page 52.)  
Press the [ PRESET CH ] button.  
1
[
[
] button: Select the next higher number preset button.  
] button: Select the next lower number preset button.  
How to play CDs  
Select the disc mode first.  
Switching disc modes  
Press the [BAND] button.  
1
When one or two CD changers are connected, press the  
[BAND] button to change modes from CD player CD  
changer 1 CD changer 2.  
The indicator will skip a changer or player that has no discs  
loaded.  
59  
How to use an optional Card remote control  
[MUTE] button  
TRACK•APS ] buttons  
[
[
DISC ] buttons  
Advancing to the next track or returning to  
the beginning of the track being played  
Press the [ TRACKAPS ] button.  
1
[
[
] button: Skips to the next track.  
] button: Returns to the beginning of the track being  
played. (Press repeatedly to move to previous  
tracks.)  
Hold the [ ] button down to fast forward, or the [ ] button to  
rewind through the track being played.  
ATTENTION  
Skipping to the next or previous disc  
Press the [ DISC ] button.  
1
[
[
] button: Selects the next higher number disc.  
] button: Selects the next lower number disc.  
Enabling the optional E-COM feature  
Pressing the [MUTE] button for one second will switch the E-COM  
feature on or off.  
60  
How to use an optional Card remote control  
[SEL] button  
[
[
TRACK ] buttons  
DISC ] buttons  
[FUNC] button [RTN] button  
Switching the remote control settings  
Remote control functions can be switched to the three patterns.  
Press the [FUNC] button of the main unit.  
1
Turn [SEL] button to select REMOTE.  
2
Press the [SEL] button.  
3
The remote control function switching mode is activated.  
Turn [SEL] button to select a pattern.  
4
The pattern is switched in the order of A, B, and C so that the  
E-com function can be supported.  
PATTERN A: Conventional functions  
PATTERN B: [DISC ] button...............Repeat  
[DISC ] button...............Answer  
[TRACK ] button............Next  
[TRACK ] button............Previous  
Other functions than the above are conventional functions.  
PATTERN C: [DISC ] button ..............Option4  
[DISC ] button ..............Option3  
[TRACK ] button ...........Option2  
[TRACK ] button ...........Option1  
Other functions than the above are conventional functions.  
Press the [RTN] button.  
5
At this time, other adjustments can also be made in Function  
Mode.  
Press the [FUNC] button to exit Function Mode.  
6
61  
How to use an optional Card remote control  
Replacing the battery  
To prevent accidents, store batteries out of the reach of  
children. If a child has swallowed one, consult a doctor  
immediately.  
Warning  
Use one CR2025 battery.  
On the back of the remote control, while pressing the  
locking knob on the battery slot cover toward your right,  
pull out the battery carrier with your fingernail.  
1
Unlock  
Remove the old battery, then place the new one in the  
carrier with the (+) mark facing up.  
2
Push in the carrier until it snaps into place.  
3
Be extremely careful not to swallow the battery.  
Caution  
62  
How to use an optional NOB remote control  
How to use an optional NOB remote control  
[AUDIO  
CONTROL]  
button  
Remote-control  
light receptor  
BAND  
MODE  
TRACK  
TUNE SEEK  
DISC  
[MUTE] button  
E-COM  
MUTE  
PWR  
[PWR] button  
ILLUMI  
Turning the power on/off  
When the power is turned on, the state used when the power was  
turned off such as CD and tuner playing is restored.  
Press the [PWR] button.  
1
The power turns on or off each time the button is pressed.  
When the main unit is shut down, the remote control will not work.  
ATTENTION  
Adjusting the audio volume  
Press the [AUDIO CONTROL] button, and turn it to the  
left or right.  
1
Each press of the button will switch the audio control modes.  
Turn to the right: Increases the volume.  
Turn to the left: Decreases the volume.  
Cutting the volume instantly (muting)  
Press the [MUTE] button for more than one second to cut the  
volume or restore it instantly.  
Press the [MUTE] button for more than one second if E-COM is  
connected and less than one second if E-COM is not connected  
ATTENTION  
to cut the volume or restore it instantly.  
63  
How to use an optional NOB remote control  
BAND  
MODE  
[BAND] button  
[MODE] button  
TRACK  
TUNE SEEK  
DISC  
E-COM  
MUTE  
PWR  
ILLUMI  
Switching playback modes  
Press the [MODE] button.  
1
Press the button to switch modes in the following sequence:  
Tuner  
Disc  
AUX  
How to play the tuner  
Select the tuner mode first.  
Selecting the FM/AM band  
Press the [BAND] button.  
1
Each press will switch tuner modes from FM1 FM2 ➔  
FM3 AM.  
64  
How to use an optional NOB remote control  
BAND  
MODE  
[BAND] button  
TRACK  
TUNE SEEK  
DISC  
[
TUNESEEK ] buttons  
[
DISC ] buttons  
E-COM  
MUTE  
PWR  
ILLUMI  
Selecting a station (manually or automatically)  
A short press of the button will allow manual station tuning.  
Pressing for more than one second will start automatic tuning.  
Press the [ TUNESEEK ] button.  
1
[
[
] button: Tunes to higher frequency stations.  
] button: Tunes to lower frequency stations.  
Selecting preset stations  
A total of six stations may be selected (preset tuning) out of  
those already set in memory through the main unit. (Refer to  
Manually setting stations into memory,page 52.)  
Press the [ DISC ] button.  
1
[
[
] button: Selects the next higher number preset button.  
] button: Selects the next lower number preset button.  
How to play CDs  
Select the disc mode first.  
Switching disc modes  
Press the [BAND] button.  
1
When one or two CD changers are connected, press the  
[BAND] button to change modes from CD player CD  
changer 1 CD changer 2.  
The indicator will skip a changer or player that has no discs  
loaded.  
65  
How to use an optional NOB remote control  
BAND  
MODE  
TRACK  
[
TRACK ] buttons  
[E-COM] button  
TUNE SEEK  
DISC  
[
DISC ] buttons  
E-COM  
MUTE  
PWR  
ILLUMI  
[ILLUMI] button  
Advancing to the next track or returning to  
the beginning of the track being played  
Press the [ TRACK ] button.  
1
[
[
] button: Skips to the next track.  
] button: Returns to the beginning of the track being  
played. (Press repeatedly to move to previous  
tracks.)  
Hold the [ ] button down to fast forward, or the [ ] button to  
rewind through the track being played.  
ATTENTION  
Skipping to the next or previous disc  
Press the[ DISC ] button.  
1
[
[
] button: Selects the next higher number disc.  
] button: Selects the next lower number disc.  
Illuminating the NOB remote control  
The buttons of the NOB remote control will be illuminated by  
pressing the [ILLUMI] button.  
Enabling the optional E-COM feature  
Pressing the [E-COM] button for one second will switch the E-COM  
feature on or off.  
66  
How to use an optional NOB remote control  
[SEL] button  
BAND  
MODE  
TRACK  
[
[
TRACK ] buttons  
DISC ] buttons  
TUNE SEEK  
DISC  
E-COM  
MUTE  
PWR  
ILLUMI  
[FUNC] button [RTN] button  
Switching the remote control settings  
Remote control functions can be switched to the three patterns.  
Press the [FUNC] button of the main unit.  
1
Turn [SEL] button to select REMOTE.  
2
Press the [SEL] button.  
3
The remote control function switching mode is activated.  
Turn [SEL] button to select a pattern.  
4
The pattern is switched in the order of A, B, and C so that the  
E-com function can be supported.  
PATTERN A: Conventional functions  
PATTERN B: [DISC ] button................Repeat  
[DISC ] button................Answer  
[TRACK ] button.............Next  
[TRACK ] button.............Previous  
Other functions than the above are conventional functions.  
PATTERN C: [DISC ] button ...............Option4  
[DISC ] button ...............Option3  
[TRACK ] button ............Option2  
[TRACK ] button ............Option1  
Other functions than the above are conventional functions.  
Press the [RTN] button.  
5
At this time, other adjustments can also be made in Function  
Mode.  
Press the [FUNC] button to exit Function Mode.  
6
67  
How to use an optional NOB remote control  
Replacing the battery  
To prevent accidents, store batteries out of the reach of  
children. If a child has swallowed one, consult a doctor  
immediately.  
Warning  
Use two AA-size batteries.  
Remove the back cover of the remote control unit by  
gently pressing and sliding it in the direction indicated by  
the arrow.  
1
Install the two batteries provided into the compartment  
as illustrated inside the compartment.  
2
Return the back cover into place by sliding it in the  
direction indicated by the arrow.  
3
68  
How to use an optional NOB remote control  
Be extremely careful not to swallow the battery.  
The battery life is approximately one year. If the remote  
control unit does not operate correctly or if the button lamp  
gets dim, replace the batteries.  
Caution  
Be sure to orient the batteries correctly so that the positive  
and negative poles match the diagram.  
Do not use one new battery and one old one; use two new  
batteries.  
Use only two of the same kind of battery.  
If any liquid is seen leaking from the batteries, remove both  
batteries and dispose of them properly. Thoroughly clean  
the battery compartment with a dry cloth. Then install new  
batteries.  
69  
How to operate the receiver with an optional CD changer connected  
How to operate the receiver with an  
optional CD changer connected  
[DISC] button  
[SEEK ] button  
[SEL]  
button  
[FAST ] button  
This section covers the operation of an optional CD changer that is  
connected to the receiver.  
To switch from another mode, press the [DISC] button.  
Listening to a CD  
Press the [DISC] button.  
1
Each press of the button switches the mode from CD Player ➔  
CD Changer 1 CD Changer 2.  
Advancing to the next track or returning to  
the beginning of the track being played  
Turn the [SEL] button to the left or right.  
1
Turn to the right: Advances to the next track.  
Turn to the left: Returns to the beginning of the track being  
played. (Repeat turning for previous tracks.)  
Fast Forward/Rewind  
Fast forward or rewind the song currently being played.  
Press and hold the [SEEK ] or [FAST ] button.  
1
[SEEK ] button: Fast forward.  
[FAST ] button: Rewind.  
70  
How to operate the receiver with an optional CD changer connected  
Buttons [4] and [5]  
Playing the beginning of tracks (SCAN)  
Press button [4].  
1
Pressing the button causes the changer to move up to the next  
track and play it for 10 seconds, then move up to the next track  
and play it for 10 seconds, and so on, on one CD, until the  
button is pressed again.  
Hold the button until the [ALL SCAN] display appears to play  
the first 10 seconds of the first track of every CD loaded.  
To continue playing a desired track, press the button again to  
stop scanning.  
ATTENTION  
After the entire disc is scanned once, ordinary playback starts  
from the point where scanning started.  
Repeating the same track (REPEAT)  
Press button [5].  
1
Pressing on the button causes the changer to repeat the track  
currently being played, until the button is pressed again.  
Hold the button until the [ALL RPT] display appears to repeat  
all tracks on the CD being played.  
71  
How to operate the receiver with an optional CD changer connected  
Buttons [1] and [2]  
Buttons [5] and [6]  
Playing tracks in random order (RANDOM)  
Press button [6].  
1
Pressing on the button causes the changer to play the tracks  
on the currently playing CD in random order.  
Hold the button until the [ALL RAND] display appears to play  
tracks from all of CDs loaded in the currently selected changer,  
in random order.  
Doing random playback, press button [5] to repeat the track  
being played. To cancel repeat play (go back to random play),  
ATTENTION  
press button [5] again.  
During playback a particular track: The track being played is  
played repeatedly.  
During searching: The following track is played repeatedly.  
Occasionally the same track happens to be played (selected)  
two or more times in a row, but it is no sign of a problem.  
When any of the functions - Playing the beginning of tracks,”  
Repeating the same trackand Playing tracks in random  
order- is selected, a message such as [SCAN], [ALL SCAN],  
[REPEAT], [ALL RPT], [RANDOM] or [ALL RAND] appears on  
the display to verify the current function.  
Skipping to the next or previous CD  
Press button [1] or [2].  
1
Button [1]: Selects the next higher number disc.  
Button [2]: Selects the next lower number disc.  
72  
How to operate the receiver with an optional CD changer connected  
Buttons [1] to [6]  
[SEL]  
button  
Specifying a CD to play  
A CD of your choice is directly selectable out of the loaded discs.  
Press the [SEL] button for less than one second.  
1
Press a button from [1] to [6].  
2
Buttons  
CD  
1
1
7
2
2
8
3
3
9
4
4
5
5
6
6
10 11 12  
To select a CD from nos. 7 to 12, press the desired button  
considerably longer.  
73  
How to operate the receiver with an optional DSP/EQ unit connected  
How to operate the receiver with an  
optional DSP/EQ unit connected  
[SOUND] button  
[SEL]  
button  
[RTN] button  
How to operate the DSP functions  
The DSP feature adds reverberations to simulate ambience in  
different types of surroundings (room sizes).  
Press the [SOUND] button.  
1
The sound adjustment mode is activated.  
Turn [SEL] button to select DSP.  
2
Press the [SEL] button.  
3
The DSP mode is activated.  
Switching room sizes  
Press the [SEL] button to switch room sizes.  
Six room sizes are available for selection in the following  
sequence:  
1
1. CONCERT (a concert hall)  
2. LIVE (a live house)  
3. CATH (a church with rich reverberations)  
4. STADIUM (an outdoor stadium)  
5. CLUB  
6. DEFEAT (DSP OFF)  
Press the [RTN] button.  
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
2
3
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
This cancels the adjustment mode; the selected room size  
will now take effect.  
74  
How to operate the receiver with an optional DSP/EQ unit connected  
[SEEK ] button  
[SEL]  
button  
[FAST ] button  
Fine-tuning an individual room-size mode  
Detailed adjustments are available in any of the room size  
modes.  
Select the room size.  
Refer to "Switching room sizes."  
1
2
Turn the [SEL] button to select the desired mode of  
adjustment.  
Items will be displayed in the following order when the  
[SEL] button is turned to the right.  
Level Duration value  
(Easily adjusted)  
EO  
LR  
LR  
ER  
ER  
(Reverberation duration)*  
(Reverberation level)*  
(Initial echo delay)  
(Initial echo level)  
S
dB  
mS  
dB  
*:  
The level and duration adjustments are available  
in CONCERT and CATH modes only.  
Press the [SEEK /FAST ] button to adjust the  
reverberation level and duration.  
3
[SEEK ] button: Increases the value.  
[FAST ] button: Decreases the value.  
75  
How to operate the receiver with an optional DSP/EQ unit connected  
Buttons [1] to [6]  
[SOUND] button  
[RTN] button  
Hold down a button, [1] to [6], for more than two  
seconds to preset a value.  
4
The preset value is overwritten by the value set using the  
above steps.  
Direct (original sound)  
Reverberation duration  
High  
Initial echo  
Level  
Time  
Long  
Initial echo delayReverberation  
Press the [RTN] button.  
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
5
6
The adjustment mode will be canceled and the selected  
room size will now take effect.  
Selecting a preset pattern from memory  
Press a preset button to select the room size in memory.  
The buttons under which room sizes are stored in memory are  
called preset buttons.  
Press a button, [1] to [6] for less than two seconds  
while in the DSP mode.  
The room size, as preset in the button, is selected.  
Press the [RTN] button.  
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
1
2
3
76  
How to operate the receiver with an optional DSP/EQ unit connected  
[SOUND] button  
[SEL]  
button  
[RTN] button  
How to operate the EQ functions  
The EQ functions enable level adjustments of various frequency  
groups for optimum listening conditions with a specific kind of music  
or musical instrument.  
Press the [SOUND] button.  
1
The sound adjustment mode is activated.  
Turn [SEL] button to select EQ.  
2
Press the [SEL] button.  
3
The EQ mode is activated.  
Switching equalizer modes  
Press the [SEL] button to switch equalizer modes.  
1
Six kinds of music categories are available for selection in  
the following sequence:  
1. POPS  
2. ROCK  
3. JAZZ  
4. CLASSIC  
5. VOCAL  
6. NEWS  
7. DEFEAT (EQ OFF)  
Press the [RTN] button.  
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
2
3
The adjustment mode will be canceled and the selected  
equalizer mode will now take effect.  
The initial EQ settings are factory preset.  
ATTENTION  
77  
How to operate the receiver with an optional DSP/EQ unit connected  
Buttons [1] to [6]  
[SEEK ] button  
[SOUND] button  
[SEL]  
button  
[RTN] button  
[FAST ] button  
Fine-tuning EQ functions  
Press the [SEL] button until the desired equalizer mode  
is displayed.  
1
Turn the [SEL] button to switch frequencies.  
2
The frequencies will switch in the following sequence:  
63Hz 125Hz 250Hz 500Hz 1kHz 4kHz 12kHz  
Press the [SEEK /FAST ] button to adjust the level.  
[SEEK ] button: Increases the value.  
[FAST ] button: Decreases the value.  
3
4
Hold down a button, [1] to [6], for more than two  
seconds to preset a value.  
When the preset value is changed, the display shows as follows:  
ATTENTION  
USER  
1~6 (Preset ch No.)  
Press the [RTN] button.  
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
5
6
This cancels the adjustment mode. The selected value will  
now take effect.  
78  
How to operate the receiver with an optional DSP/EQ unit connected  
Buttons [1] to [6]  
[SOUND] button  
[RTN] button  
Selecting an equalizer mode from memory  
Press a preset button to select the equalizer mode set in  
memory for the button.  
The buttons that set equalizer modes in memory are called  
preset buttons.  
Press the button, [1] to [6] for less than two seconds  
while in the EQ mode.  
1
Press the [RTN] button.  
2
At this time, other adjustments can also be made in Sound  
Adjustment Mode.  
Press the [SOUND] button to exit Sound Adjustment  
Mode.  
3
79  
Others  
Others  
[DISC] button  
Connecting Portable Audio Players to the AUX Jack  
Use a commonly available accessory cord with stereo mini-plug to  
connect the audio output jack (LINE) or headphone jack of a  
portable audio player to the AUX (auxiliary) jack of this system.  
Turn on the portable audio player and start its play  
function.  
1
Switch to AUX mode by pressing the [DISC] button for  
more than one second.  
2
Activation of the AUX mode will light the "AUX" indicator and  
channel audio player output to the system speakers.  
While the AUX mode is activated, actions such as turning off the  
audio player or pulling out the connection cord may cause  
ATTENTION  
noise spikes that can damage the system speakers. Be sure to  
avoid this possibility by turning off system power or switching  
from AUX mode to another mode before shutting off or  
disconnecting the portable audio player.  
Audio output levels will differ for the various devices that can be  
connected by this method. Carefully adjust volume until the  
output level of the connected player is known.  
Before using a portable audio player in a vehicle, read the  
player's operation manual carefully and confirm problem-free  
operation in the vehicle before proceeding.  
80  
If you have a question:  
If you have a question:  
[RESET] button  
First check the items mentioned below before attempting to  
troubleshoot problems.  
If a problem occurs, for instance when the unit does not respond  
to any button presses, or the display doesn't work correctly,  
Caution  
press the [RESET] button using a sharp tool.  
Pressing the [RESET] button will delete all the entries from  
memory. The settings will return to those made at the factory  
prior to shipment.  
81  
If you have a question:  
Displayed information (for troubleshooting)  
The information listed in the chart below is displayed to show the  
status of the CD player and CD changer. Refer to the chart for the  
appropriate action.  
Information Code Table  
When "INFO " flashes on the indicator  
Nos.2~7 are displayed.  
Information Contents  
Explanation and remedial action to take  
2
3
5
NO DISC LOADED IN  
THE MAGAZINE  
There is no disc in the magazine or player. Load  
a disc in the magazine. (Load a music disc.)  
DISCS ARE DIRTY OR  
DAMAGED  
The loaded disc is dirty or upside down. Check  
it for proper orientation and verify it is clean.  
CD PLAYER AND CD  
CHANGER FAILS  
MECHANICALLY  
The CD player and CD changer is inoperative for  
some reason. Go through the magazine removal  
procedure.  
If a magazine fails to eject, have your dealer fix  
the problem.  
6
7
WHEN THE CD CHANGER  
INTERNAL TEMPERATURE IS operation. Wait till it cools down.  
HIGH (TO PROTECT PICKUP Resume playing after the High temperature sensed  
UNIT)  
The temperature in the CD changer is too high for  
and CD stopped" display disappears. If the CD still  
cannot play, have your dealer repair it.  
AN INTERNAL POWER  
SUPPLY FAILURE IS  
Turn the ACC off once before turning it on once  
again to resume the operation.  
OCCURRING WITH THE If the function still cannot be restricted, contact your  
AUTO CHANGER  
dealer.  
Information Contents  
LOAD  
Explanation and remedial action to take  
CD changer is in the process of verifying the  
presence of CDs after a magazine has been inserted  
into the CD changer.  
82  
If you have a question:  
Remedial action  
Refer  
Mode  
Problem  
Causes  
to take  
to page  
Is the volume control up sufficiently?  
Turn up the volume control.  
23  
23  
Is the muting function in effect  
(MUTE)?  
Cancel the muting  
(MUTE) function.  
Readjust the fader and  
balance controls to more  
normal positions.  
Dead or  
weak sound  
Is the fader or balance control set far  
to one side?  
24  
Other probable causes include  
broken audio-signal wiring or a faulty  
speaker.  
Have your dealer check  
the problem.  
Are too many electrical items  
installed, causing a lack of power?  
Have your dealer check  
the problem.  
Power does  
not turn on.  
Other probable causes include a  
run-down car battery, broken power  
or interconnection wiring.  
Have your dealer check  
the problem.  
Has the car battery been disconnected  
for repair or checked out?  
Reenter them into  
memory.  
51,  
52  
Common  
to all  
Are too many electrical items  
installed and causing lack of  
available power?  
Have your dealer check  
the problem.  
Frequencies  
or titles set in  
memory are  
deleted.  
Other probable causes include  
run-down car battery, broken power  
or interconnection wiring.  
Have your dealer check  
the problem.  
No guide  
tone sounds.  
Is the guide tone disabled?  
Is the battery low?  
Enable the guide tone.  
Replace battery.  
28  
62,  
68  
Is the battery installed in reverse  
polarity?  
Reinstall the battery in the  
correct polarity.  
62,  
68  
The remote  
control does  
not work.  
Is direct sunlight hitting the remote  
control light receptor?  
Use the remote control  
close to the receptor.  
Other probable causes include a  
malfunctioning remote control.  
Have your dealer check  
the problem.  
83  
If you have a question:  
Remedial action  
to take  
Refer  
Mode  
Problem  
Causes  
to page  
Is an extra label or seal  
applied to the disc?  
Do not apply labels or seals  
to the disc.  
The disc cannot be inserted.  
The disc is ejected as soon  
as it is insertaed.  
11  
Are there rough edges,  
deformations or  
damaged areas on the  
disc?  
Try inserting another disc.  
Removed any burrs.  
Do not use a deformed or  
damaged disc.  
Or, the disc cannot be  
ejected.  
The disc cannot be  
changed.  
12  
Is the disc damaged?  
(scratched, warped, etc.) play a damaged disc.  
Try another disc. Do not  
11  
13  
Is the disc clean?  
Clean the disc.  
CD  
Sound skips around.  
Sound is intermittent.  
Sound is bad in quality.  
Is the player mounted at  
a proper angle?  
Is the player mounted  
loosely?  
Have your dealer check it  
out.  
Are you driving over a  
rough surface?  
Avoid playback while  
driving over rough surfaces.  
10  
Press the [DISC] button a  
bit longer and then press  
the [OPEN] button (forced  
Eject).  
The disc cannot be  
ejected.  
If unknown  
Remedial action  
to take  
Refer  
Mode Problem  
Causes  
to page  
Is the antenna retracted?  
Extend the antenna.  
Is the tuner correctly tuned to a  
station?  
50  
50  
Tune to a station.  
Tune to a local station.  
(Please note, there may  
be no local stations  
servicing the area where  
you are currently driving.)  
Receives  
no  
Are you driving outside the service  
area of your preset stations?  
stations,  
or  
Tuner  
receives  
static  
noise.  
Are you operating other equipment  
with a computer, or a mobile phone,  
in your vehicle at the same time as  
your receiver?  
Avoid operating such  
equipment while using  
the receiver.  
Other problems may include a loose Have your authorized  
or disconnected antenna cable, a  
bad antenna cable or a bad  
Eclipse retailer check the  
problem.  
84  
Specifications  
Specifications  
<GENERAL>  
Power Supply  
Current Drain  
14.4V DC (11-16V)  
3A MAX  
Dimensions (W x H x D)  
In-Dash Unit  
Mass (weight)  
7" x 2" x 6-1/8" (178 x 50 x 155mm)  
Approx. 1.4kg  
<FM TUNER>  
Frequency Range  
Usable Sensitivity  
Frequency Response  
Stereo Separation  
87.75~107.9MHz (200kHz step)  
13dBf  
30~15,000Hz,  
38dB  
3dB  
<AM TUNER>  
Frequency Range  
Usable Sensitivity  
530~1,710kHz (10kHz step)  
20µV  
<CD SECTION>  
Frequency Response  
Wow & Flutter  
20~20,000Hz,  
Below measurable limits  
3dB  
Stereo Separation  
S/N Ratio (A-weighted)  
Dynamic Range  
80dB  
95dB  
95dB  
Total Harmonic Distortion  
0.006%  
<AUDIO AMPLIFIER>  
Power Output  
13W x 4 (20~20,000Hz, 0.8% THD,  
4) Max. 50W x 4  
Output Level/Impedance  
Tone Action  
5V (0dB CD)  
55line-out impedance  
Bass:  
12dB at 63/100Hz  
Treble:  
12dB at 8k/10kHz  
Loudness  
+10dB at 100Hz/+6dB at 10kHz  
85  
Before installation  
Before installation  
O Note O  
Be sure to disconnect the battery's negative terminal before  
installing the receiver.  
Components  
No.  
Item  
Q'ty  
1
2
3
4
5
6
7
8
9
Main unit  
Mounting sleeve  
Side bracket  
Rear bracket  
Bezel  
Bushing  
Self-tapping screw (6 x 16 mm)  
Stud bolt  
Flat head screw (5 x 8 mm)  
Hex-head bolt (5 x 20 mm)  
Hex nut (5 mm)  
1
1
2
1
1
1
2
1
4
2
2
1
10  
11  
12  
Interconnecting cable  
Setting the system-selector switch  
When this receiver is used in combination with an external amplifier,  
DSP, etc., the selector switch on the left side of the main unit may  
have to be switched.  
Set the switch according to the table below:  
External amplifier  
DSP/EQ/XOVER  
Switch  
None  
None  
Connected  
Connected  
None  
OFF*  
ON  
OFF*  
OFF*  
Connected  
Connected  
None  
* : Pattern of selector switch at shipping  
MAIN UNIT LEFT SIDE VIEW  
86  
Before installation  
Installation angle  
In order to maintain proper functioning, install the unit within an angle  
of 30 degrees from horizontal (standard). If this is not done, sound  
skipping or ejection of the CD may occur.  
FRONT  
WITHIN AN ANGLE  
OF 30 DEGREES  
STANDARD  
87  
Mounting instruction  
Mounting instruction  
Mounting the main unit  
Insert the mounting sleeve into the opening in the vehicle  
console.  
1
Use a screwdriver or the like to bend the tabs in the  
mounting sleeve to secure the mounting sleeve.  
2
BEND THE MOUNTING  
TABS.  
DASH BOARD  
OR CONSOLE  
2 MOUNTING  
SLEEVE  
Attach the side brackets to the main unit using flathead  
screws.  
3
1 MAIN UNIT  
9 FLAT HEAD  
SCREWS [ x 2 ]  
(5 x 8mm)  
3
SIDE BRACKETS [ x 2 ]  
88  
Mounting instruction  
Mount the stud bolt to the main unit.  
4
5
Insert the main unit into the mounting sleeve until it locks  
in place.  
Fasten the rear of the main unit using either method [A]  
or [B].  
6
Select method [A] or [B] to suit the interior configuration of the  
vehicle.  
Install the bezel on the main unit.  
7
Some automobiles may be equipped to secure the back of the  
main unit using the stud bolt and supplied rubber support.  
METAL OF  
VEHICLE  
[A]  
DASH BOARD  
OR CONSOLE  
6
BUSHING  
TOP  
P
8
STUD BOLT  
2
MOUNTING SLEEVE  
5
BEZEL  
7 SELF TAPPING  
SCREW (6 x 16mm)  
11  
NUT (5mm)  
[B]  
DASH BOARD  
METAL OF  
VEHICLE  
OR CONSOLE 10  
BOLT  
(5 x 20mm)  
11  
NUT (5mm)  
TOP  
4
REAR BRACKET  
8
STUD BOLT  
2
MOUNTING SLEEVE  
5
BEZEL  
89  
Mounting instruction  
O Note O  
To prevent unconnected leads from shorting out, insulate them  
by wrapping their tips with electrical tape. Similarly, insulate the  
ends of connected leads.  
If an external amplifier is to be connected to the receiver, be  
sure to ground its outside housing to the vehicle body (a metal  
part).  
Names of lead wires and destinations (refer to Page 92)  
No.  
Name  
Wire color  
Destination  
1
ACC  
Red  
Connect where the power comes on  
when the ignition is in the ACC  
position.  
2
B+  
Yellow  
Black  
Connect where the power is constantly  
available, regardless of the ignition  
switch's position.  
3
4
5
6
7
Ground  
Connect where good body grounding  
is available.  
Antenna power supply Blue  
Connect to the automatic-antenna  
control terminal of the vehicle.  
Lamp power supply  
Orange/White  
Connect to where power comes on  
when the headlights are turned on.  
Control power supply Blue/White  
E-LAN terminal  
Connect to the control terminal for  
the external amplifier, etc.  
Connect to the E-LAN terminal of the  
CD changer, DSP, etc.  
8 & 9 Line-in/out terminals  
Connect to the RCA input connectors  
of an external amplifier,or to the RCA  
output connectors of a DSP or EQ.  
10  
Line-out terminals  
(Nonfader)  
Connect to the RCA input connectors  
of a DSP or EQ, or the RCA connectors  
of a woofer amplifier.  
11  
12  
13  
14  
15  
Speaker terminals  
Cellular phone mute  
Digital out terminal  
Connect them to their respective  
speakers.  
Pink  
Connect to the ground output terminal  
on a mobile phone.  
Connect to digital input terminal of the  
Eclipse Commander module.  
Eclipse Commander terminal  
Line in terminal  
Connect to the Eclipse Commander  
module.  
Connect to the mini plug (φ3.5)  
output connector of Portable unit  
(MP3 player, MD player, etc).  
90  
Mounting instruction  
System  
CD5423  
CD5423  
CH3083  
CD5423  
CH3083  
CH3083  
91  
Mounting instruction  
92  
Mounting instruction  
93  
Mounting instruction  
94  
IMPORTANT  
RECORD YOUR “KEY CD”  
HERE…  
STORE YOUR “KEY CD”  
ALONG WITH YOUR  
OWNER’S MANUAL IN  
YOUR SOCK DRAWER.  
95  
CUSTOMER NOTICE  
Please retain this booklet and write in the serial number of your CD5423 for  
identification. The serial number is labeled or stamped on the chassis.  
Serial No.  
DIVISION OF FUJITSU TEN CORP. OF AMERICA  
19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502  
(310) 327-2151  
090001-1440A700  
0303 (Y.O)  

Alpine In Dash GPS Navigation Receiver INA W900 User Manual
Ariston Benchmark System A 24 RFF User Manual
AT&amp;T HEADSET COMPATIBILITY WHEEL TL7610 User Manual
BlueAnt Wireless EzyTalk User Manual
Bosch Appliances UC MCM 5200 User Manual
Bushnell Night Vision 26 26 4366 User Manual
Canon UC 16 User Manual
Continental Electric CE22151 User Manual
Fusion Electronics Car Speaker PF SW120D4 User Manual
Hanns G Car Video System HSG 1082 User Manual